濟南油煙凈化器會隨著使用時間的增長，內部堆積很多的油漬，如果不及時的進行清洗，那么很難達到好的凈化效果，接下來給大家介紹一下油煙凈化器清洗工作的規范內容。

Jinan lampblack purifier will accumulate a lot of oil stains with the increase of use time. If it is not cleaned in time, it will be difficult to achieve a good purification effect. Next, I will introduce the standard content of lampblack purifier cleaning.

1、關閉電源并給負載放電

1. Turn off the power supply and discharge the load

關閉機身上的電源開關，但由于電箱內有電，在維修設備前要關閉濟南油煙凈化器外的總電源開關。請勿帶電作業，以確保清潔工的安全。

Turn off the power switch on the machine body, but because there is electricity in the electric box, turn off the main power switch outside the Jinan lampblack purifier before maintaining the equipment. Do not work with electricity to ensure the safety of cleaners.

打開設備檢修門后，在去除電場之前，釋放電場中的殘留電荷。使用螺絲刀將放電場中的殘余電荷放電。具體操作是用手握住螺絲刀的絕緣手柄，利用螺絲刀的金屬部分在電場中縮短明顯圓柱體的陰力。

After opening the equipment access door, release the residual charge in the electric field before removing the electric field. Use a screwdriver to discharge the residual charge in the discharge field. The specific operation is to hold the insulated handle of the screwdriver by hand, and use the metal part of the screwdriver to shorten the negative force of any cylinder in the electric field.

用戶在清理電場時，要嚴格及時清理機箱內部的油漬，以消除火災隱患。

When cleaning the electric field, users should strictly and timely clean the oil stains inside the chassis to eliminate the potential fire hazard.

2、擰下螺絲并去除電場

2. Unscrew the screws and remove the electric field

確認電源已關閉后，拆下固定螺栓，打開維修門，用手拉動兩側電場，待電場即將釋放時，用手握住前端。避免突然跌落損壞電場。

After confirming that the power supply has been turned off, remove the fixing bolts, open the maintenance door, pull the electric field on both sides by hand, and hold the front end by hand when the electric field is about to release. Avoid sudden drop to damage the electric field.

3、取下附件以方便清潔

3. Remove accessories for cleaning

由于絕緣體上的潮濕土壤很可能是造成漏電的原因，因此在移除絕緣體的同時，將針與陰力分開，將針筒與陽力分開，更容易清潔。

As the damp soil on the insulator is likely to be the cause of electric leakage, it is easier to clean by separating the needle from the negative force and the needle cylinder from the positive force while removing the insulator.

4、清洗、浸泡、沖洗電場

4. Cleaning, soaking and washing electric field

使用不銹鋼或塑料清洗罐式容器，形狀大于電場。清潔時將油煙凈化器包裹起來，以免弄臟地板，然后將包裹排放到容器中。用重量比為1:20的堿和熱水混合溶液起泡清洗時，浸泡時間視油漬程度而定。浸泡后，用高壓水槍沖洗干凈，放在干凈的地方晾干。

Use stainless steel or plastic to clean the tank container, which is larger than the electric field. When cleaning, wrap the oil fume purifier to avoid soiling the floor, and then discharge the package into the container. When the mixed solution of alkali and hot water with a weight ratio of 1:20 is used for foaming cleaning, the soaking time depends on the degree of oil stain. After soaking, wash it with a high-pressure water gun and place it in a clean place to dry.

5、絕緣子的檢查和清洗

5. Inspection and cleaning of insulators

如果絕緣子在檢查過程中燃燒，如果破裂則更換。您需要將絕緣子和絕緣子上的油清洗干凈并擦干。在清潔方法中，將酒精噴在絕緣體上，然后用干布擦拭。

If the insulator burns during inspection, replace it if it breaks. You need to clean the insulator and oil on the insulator and wipe it dry. In the cleaning method, spray alcohol on the insulator and then wipe it with a dry cloth.

以上是油煙凈化器按照規范進行清洗工作的步驟，以上清洗方法都比較仔細，在操作過程中要注意不要損壞某些部件。配件的拆卸也要按照一定的規范進行。關注我們http://m.zypolishing.com了解更多事項！

The above steps are the steps for cleaning the lampblack purifier according to the specifications. The above cleaning methods are very careful. Pay attention not to damage some parts during the operation. The accessories shall also be disassembled according to certain specifications. Follow us http://m.zypolishing.com Learn more!