通風管道設備假設長期堆積雜質,這些雜質長期的滯留在機械設備內,在運轉中會加快它的油凝結,溫渡過高,構成氣壓閥、液壓等部件的損壞,對正常運轉構成很大的影響所以定期的對通風管道設備中止一次多維度的清理是非常有必要的。比如：
It is assumed that impurities are accumulated in the ventilation pipe equipment for a long time. These impurities will stay in the mechanical equipment for a long time, which will accelerate its oil condensation during operation. The temperature transition is too high, which will cause damage to the pneumatic valve, hydraulic and other components, and have a great impact on the normal operation. Therefore, it is very necessary to stop a comprehensive cleaning of the ventilation pipe equipment on a regular basis. For example:
一些情況下需求在每日運轉后中止清理,那就要每日都清理的,需求每個月清理一次的就要每個月對它清理一次,每次清理都要做好相應的清理記載,從而延長通風管道設備的運用壽命
In some cases, if it is required to stop cleaning after daily operation, it should be cleaned every day. If it is required to clean once a month, it should be cleaned once a month. Corresponding cleaning records should be made for each cleaning, so as to prolong the service life of ventilation pipe equipment
通風管道設備好三個月中止一次多維度清理,這是由于,通風管道設備在長期運轉當中,通常會產生一定的堆積物,而這些雜質會影響它液壓系統(tǒng)的液壓油的質量,假設這些雜質進入到油中并繼續(xù)運轉,又會構成更多的灰塵和雜質的進入,從而構成液壓系統(tǒng)中油管的雜物增加,運轉速度變慢,壓力減小,以致無法運轉等現象
The ventilation pipe equipment shall be completely cleaned every three months. This is because the ventilation pipe equipment usually produces certain deposits during long-term operation, and these impurities will affect the quality of the hydraulic oil of its hydraulic system. Assuming that these impurities enter the oil and continue to operate, they will form the entry of more dust and impurities, which will increase the sundries of the oil pipe in the hydraulic system, slow down the operation speed and reduce the pressure, So that it can not operate, etc
山東通風管道加工廠家提醒，還有就是一些通風管道設備假設長期堆積雜質,這些雜質長期的滯留在機械設備內,在運轉中會加快它的油凝結,溫渡過高,構成氣壓閥、液壓等部件的損壞,對正常運轉構成很大的影響。比如說：
Shandong ventilation pipe manufacturers remind that some ventilation pipe equipment is supposed to accumulate impurities for a long time. These impurities will stay in the mechanical equipment for a long time, which will accelerate its oil condensation during operation. The temperature transition is too high, which will cause damage to air pressure valve, hydraulic and other components, and have a great impact on normal operation. for instance:
當風道與除塵設備、加熱設備等銜接前，應待設備裝置終了后，按理論測繪的圖紙中止預制和裝置。通風管道裝置時，進、出風日宜在風道預制時開出洞口，如需在裝置終了的風道上現開風口，其接口處應緊密。
When the air duct is connected with the dust removal equipment, heating equipment, etc., the prefabrication and installation shall be suspended according to the theoretical mapping drawings after the equipment and installation are completed. When installing the ventilation duct, the air inlet and outlet shall be opened during the prefabrication of the air duct. If it is necessary to open an air outlet on the air duct at the end of the device, the interface shall be tight.
當運送含凝結水或含濕量較大的氣體時，其水平管道宜設有坡度，并在低點處接排水管。裝置時風道底部不宜呈現縱向接縫，對底部有接縫處應中止密封處置。對運送易燃、易爆氣體的鋼板風道，在風道銜接法蘭處應裝置跨接線，并與靜電接地網銜接。
When transporting gas with condensate or high moisture content, its horizontal pipeline should be provided with a slope and connected with a drainage pipe at the low point. During installation, the bottom of the air duct should not have longitudinal joints, and the sealing treatment should be suspended at the joints at the bottom. For steel plate air duct transporting flammable and explosive gas, jumper wire shall be installed at the connecting flange of air duct and connected with electrostatic grounding grid.
當水平風道高度在4m以上時，裝置人員應系安全帶。腳手架或移動式支架上的跳板應固定好，跳板寬度應契合安全規(guī)范，在腳手架上的裝置人員宜攜東西袋，避免東西或電鉆等物掉落傷人。雙吊桿支架在風道就位后，應保證橫擔平直，吊桿不改動，雙吊桿受力均勻。
When the height of the horizontal air duct is above 4m, the installation personnel shall wear safety belts. The springboard on the scaffold or mobile support shall be fixed properly, and the width of the springboard shall conform to the safety specifications. The installation personnel on the scaffold should carry bags to avoid falling things or electric drills and other objects from injuring people. After the double suspender support is in place in the air duct, ensure that the cross arm is straight, the suspender is not changed, and the double suspender is stressed evenly.
The above is the relevant content about the problem shared for you today. I hope it can help you. If you want to know more, you can contact us by phone or follow our website http://m.zypolishing.com 。
上一篇：油煙凈化器的凈化效果變差目前有三個原因
下一篇：想讓油煙凈化器達到滿意凈化效果有幾個前提
